TW-1 ETP Electrical Metallic Tubing (EMT) Fittings and Liquidtight Flexible Metallic Conduit Connectors T W- 1 — S t e e l c o n n e c t o r s and couplings including gland compression, and set screw types. Type 4000 Set Screw Connector Type 5000 Set Screw Coupling UL Listed Raintight ETP steel EMT connectors and couplings. Flexel™ hand-bendable steel flexible fittings. Steel liquidtight flexible metallic conduit connectors. Type 6000 Compression Coupling Type 7000 Compression Connector Type 4QS Liquidtight Connectors Flexel™ Type FLA Flexible Fittings TW TW-2 — Combination couplings, 90° connectors, cap/hoods, conversion adapter, clamps and straps. Benders and high strength steel handles. TWCC-50 Combination Coupling TWL-50L 90° Connector TWCL-50 Clamp TW2500 Strap Effective September, 2005 Copyright 2005 EF-125 Entrance Cap Standard Bender With Degree Scale 800-621-1506 www.appletonelec.com PAGE 1 TW-1 File # E14815 Steel EMT Set-Screw Connectors and Couplings 4000S Series Connectors Features • Heavy steel walls. • Concretetight when taped. • Pre-set/Pre-staked set screws. • Male hub threads NPS. • Available with insulated throat. • Three-way combination screws. • Insulated throat connector rated 90°C. Standard Materials • Steel. Standard Finish • Zinc Plated. Third Party Certification • UL Listed: E-14815 (1/2” to 2”) • UL Listed: E-14816 (2-1/2” to 4”) Applicable Third Party Standards • UL 514B • CSA Standard C22.2 No. 18 • NEMA FB-1 • Federal Spec. W-F-408E Type 4050S — Type 4100S Type 4125S — Type 4400S Trade Size (inches) Catalog Number Insulated Throat Catalog Number 1/2 3/4 1 1-1/4 4050S 4075S 4100S 4125S 4050ST 4075ST 4100ST 4125ST 1-1/32 1-3/32 1-3/16 1-3/4 27/32 1-5/64 1-5/16 1-11/16 1-1/2 2 2-1/2 3 4150S 4200S 4250S 4300S 4150ST 4200ST 4250ST 4300ST 1-15/16 2-3/16 2-3/8 2-7/8 3-1/2 4 4350S 4400S 4350ST 4400ST 3 3-3/16 Dimensions in Inches Body Max Thread Length Dia. Length Wt. Lbs. Per 100 Ctn. Qty. Std. Pkg. 7/16 7/16 7/16 9/16 10 15 23 42 25 20 20 10 250 200 100 40 1-15/16 2-3/8 3-1/8 3-3/4 9/16 5/8 7/8 7/8 53 75 130 230 10 5 — — 40 20 10 5 4-1/4 4-3/4 1 1 250 250 — — 5 5 5000S Series Couplings TW Features • Heavy steel walls. • Concretetight when taped. • Pre-set/Pre-staked set screws. • Three-way combination screws. Standard Materials • Steel. Standard Finish • Zinc Plated. Third Party Certification • UL Listed: E-14815 (1/2” to 2”) • UL Listed: E-14816 (2-1/2” to 4”) Applicable Third Party Standards • UL 514B • CSA Standard C22.2 No. 18 • NEMA FB-1 • Federal Spec. W-F-408E All dimensions are approximate and subject to change. Effective September, 2008 Copyright 2008 PAGE 2 Type 5050S — Type 5100S Trade Size (Inches) Catalog Number Type 5125S — Type 5400S Dimension in Inches Body Length Max. Dia. Wt. Lbs. Per 100 Ctn. Qty. Std. Pkg. 1/2 5050S 1-3/4 27/32 10 25 250 3/4 1 1-1/4 5075S 5100S 5125S 2-1/8 2-1/2 3-1/4 1-5/64 1-5/16 1-11/16 16 25 45 20 20 10 200 100 40 1-1/2 2 2-1/2 3 5150S 5200S 5250S 5300S 3-3/4 4 4-1/4 4-1/2 1-15/16 2-3/8 3-1/8 3-3/4 60 82 166 213 10 5 — — 40 20 10 5 3-1/2 4 5350S 5400S 4-3/4 5 4-1/4 4-3/4 260 300 — — 5 5 800-621-1506 www.appletonelec.com TW-1 File # 14815 Steel EMT Compression Connectors and Couplings 6000S Series Couplings Features • Concretetight. Standard Materials • Steel Body and Nut. Standard Finish • Zinc Plated Third Party Certification • UL Listed: E-14815 (1/2” to 2”) • UL Listed: E-14816 (2-1/2” to 4”) • Listed Concretetight 1/2” through 4”. Applicable Third Party Standards • UL 514B • CSA Standard C22.2 No. 18 • NEMA FB-1 • Federal Spec. W-F-408E Type 6050S — Type 6400S Trade Size (Inches) Catalog Number Dimension in Inches Body Length Max. Dia. Wt. Lbs. Per 100 Ctn. Qty. Std. Pkg. 1/2 6050S 1-3/8 3/4 6075S 1-1/2 27/32 19 25 250 1-3/8 25 20 1 6100S 200 1-21/32 1-5/16 39 20 1-1/4 100 6125S 2-1/2 1-11/16 88 5 25 1-1/2 6150S 2-1/2 1-15/16 104 5 25 2 6200S 2-1/2 2-3/8 149 2 10 2-1/2* 6250S 4-1/4 3-1/8 240 — 10 3* 6300S 4-1/2 3-3/4 350 — 5 3-1/2* 6350S 4-3/4 4-1/4 475 — 5 4* 6400S 5 4-3/4 600 — 5 * Rated for steel EMT, Aluminum and steel RMC, and steel IMC. 7000S Series Connectors All dimensions are approximate and subject to change. TW Features • Male hub threads NPS. • Available with insulated throat. • Concretetight. • Insulated throat connector rated 90°C. Standard Materials • Steel Body and Nut. Standard Finish • Zinc Plated Third Party Certification • UL Listed: E-14815 (1/2” to 2”) • UL Listed: E-14816 (2-1/2” to 4”) • Listed Concretetight 1/2” through 4”. Applicable Third Party Standards • UL 514B • CSA Standard C22.2 No. 18 • NEMA FB-1 • Federal Spec. W-F-408E Type 7050S — Type 7400S Trade Size Catalog (inches) Number Insulated Throat Catalog Number Dimensions in Inches Body Max Thread Length Dia. Length Wt. Lbs. Per 100 Ctn. Qty. Std. Pkg. 1/2 3/4 1 1-1/4 7050S 7075S 7100S 7125S 7050ST 7075ST 7100ST 7125ST 1-1/8 1-1/32 1-1/4 1-13/16 1-1/16 1-1/4 1-9/16 2 3/8 7/16 7/16 9/16 15 21 32 72 25 25 20 5 250 250 200 25 1-1/2 2 2-1/2* 3* 7150S 7200S 7250S 7300S 7150ST 7200ST 7250ST 7300ST 2 2-1/4 2-3/8 2-7/8 2-3/16 2-11/16 3-11/32 4 9/16 11/16 7/8 7/8 85 124 160 265 5 2 — — 25 10 10 5 3-1/2* 4* 7350S 7400S 7350ST 7400ST 3 3-3/16 4-1/2 5-1/16 1 1 425 600 — — 5 5 * Rated for steel EMT, Aluminum and steel RMC, and steel IMC. Effective September, 2008 Copyright 2008 800-621-1506 www.appletonelec.com PAGE 3 TW-1 File # 14815 EMT Steel Set-Screw Connectors & Couplings-USA 4000US Series Connectors Features: • Heavy steel walls • Concretetight when taped • Pre-set/Pre-staked set screws • Male hub threads NPS • Available with insulated throat • Three-way combination screws 1/2” through 2” • Slotted hexhead screws 2-1/2” through 4” • Insulated throat temperature rating = 90°C. Material/Finish: • Steel/Zinc Plated Third Party Certification: • UL Listed: E-14895 • CSA Certified File No. 28507 Applicable Third Party Standards: • UL Standard: 514B • CSA Standard: C22.2 No. 18 • NEMA: FB-1 • Federal Spec: W-F-408E 5000US Series Couplings TW Features: • Heavy steel walls • Concretetight when taped • Pre-set/pre-staked set screws • Three-way combination screws 1/2” through 2” • Slotted hexhead screws 2-1/2” through 4” Material/Finish: • Steel/Zinc Plated Third Party Certification: • UL Listed: E-14895 • CSA Certified: 28507 Applicable Third Party Standards: • UL Standard: 514B • CSA Standard: C22.2 No. 18 • NEMA: FB-1 • Federal Spec: W-F-408E Insulated Throat Catalog Number Body Length Max Dia. Thread Length /2 4050US 4050UST /4 4075US 4075UST 1 4100US 4100UST 11/4 4125US 4125UST 1-5/32 1-7/32 1-1/2 1-11/16 1 1-7/32 1-1/2 1-29/32 3/8 13/32 7/16 1/2 11/2 2 21/2 3 1-29/32 2 2-5/8 3-1/16 2-5/32 2-21/32 3-3/4 4-9/16 17/32 19/32 1-1/4 1-3/8 Trade Size Catalog (inches) Number 1 3 4150US 4200US 4250US 4300US 4150UST 4200UST 4250UST 4300UST Dimensions in Inches 31/2 4350US 4350UST 3-1/16 5-11/16 1-13/32 4 4400US 4400UST 3-11/32 5-23/32 1-1/2 Type 4050US — Type 4200US Trade Size (inches) /2 /4 1 11/4 5050US 5075US 5100US 5125US 1-1/2 1-1/2 1-7/8 2-3/16 7/8 1-1/8 1-13/32 1-3/4 11/2 2 21/2 3 5150US 5200US 5250US 5300US 2-19/32 2-11/16 2-3/4 3-1/8 2-1/32 2-1/2 3-15/16 4-9/16 31/2 4 5350US 5400US 3-5/32 3-3/8 5-1/16 5-23/32 1 3 PAGE 4 Type 4250US — Type 4400US Dimensions in Inches Catalog Number Body Length Dia. Type 5050US — Type 5200US Effective September, 2008 Copyright 2008 Made in the USA Made in the USA Type 5250US — Type 5400US 800-621-1506 www.appletonelec.com TW-1 File # 14815 EMT Steel Compression Connectors & Couplings 7000US Series Connectors Features: • Male hub threads NPS • Available with insulated throat • Concretetight • Insulated throat temperature rating = 90°C. Material: • Steel Body & Nut Finish: • Zinc Plated Third Party Certification: • UL Listed: E-14895 • Listed Concretetight 1/2” - 4” • CSA Certified: 28507 Applicable Third Party Standards: • UL Standard: 514B • CSA Standard: C22.2 No. 18 • NEMA: FB-1 • Federal Spec: W-F-408E Features: • Concretetight Material: • Steel Body & Nut Finish: • Zinc Plated Third Party Certification: • UL Listed: E-14895 • Listed Concretetight 1/2” - 4” • CSA Certified: 28507 Applicable Third Party Standards: • UL Standard: 514B • CSA Standard: C22.2 No. 18 • NEMA: FB-1 • Federal Spec: W-F-408E Insulated Dimensions in Inches Throat Catalog Body Max Thread Number Length Dia. Length /2 /4 1 11/4 7050US 7075US 7100US 7125US 7050UST 7075UST 7100UST 7125UST 1-1/16 1-1/8 1-1/4 1-7/16 31/32 1-7/32 1-1/2 1-29/32 3/8 13/32 7/16 1/2 11/2 2 21/2 3 7150US 7200US 7250US 7300US 7150UST 7200UST 7250UST 7300UST 1-9/16 1-11/16 4-1/16 4-1/8 2-5/32 2-11/16 4-1/8 4-11/16 17/32 19/32 1-1/4 1-3/8 31/2 4 7350US 7350UST 7400US 7400UST 4-1/4 4-1/2 5-11/32 1-13/32 5-7/8 1-1/2 1 3 Type 7050US — Type 7200US Trade Size (inches) 6050US 6075US 6100US 6125US 1-11/32 1-11/32 1-13/32 1-3/4 31/32 1-7/32 1-1/2 1-29/32 11/2 2 21/2 3 6150US 6200US 6250US 6300US 1-7/8 2-1/8 5-1/2 5-1/2 2-5/32 2-11/16 4-1/8 4-11/16 31/2 4 6350US 6400US 5-5/8 5-3/4 5-11/32 5-7/8 3 Type 6050US — Type 6200US Effective September, 2008 Copyright 2008 Type 7250US — Type 7400US Dimensions in Inches Catalog Number Body Length Max. Dia. /2 /4 1 11/4 1 Made in the USA TW 6000US Series Couplings Trade Size Catalog (inches) Number Made in the USA Type 6250US — Type 6400US 800-621-1506 www.appletonelec.com PAGE 5 TW-1 File # E14815 UL Listed Raintight Steel EMT Compression Connectors and Couplings Raintight Gland Compression Connector – 7000SR Series Use: To ground and secure EMT raceway to boxes and enclosures in wet locations. Features: • UL Listed Raintight • InspectoRidgeª external visual inspection aid — See below • No disassembly required • Male hub threads NPS • Available with and without insulated throat • Concretetight Material/Finish: • Steel Body & Nut Zinc Electroplated • Silicone Rubber Internal Sealing Ring • EPDM Rubber KO Sealing Ring Raintight Gland Compression Coupling Type – 6000SR Series TW Use: To ground and secure EMT raceway sections together in wet locations. Features: • UL Listed Raintight • InspectoRidgeª external visual inspection aid — See below • No disassembly required • Concretetight Material/Finish: • Steel Body & Nut Zinc Electroplated • Silicone Rubber Internal Sealing Rings Third Party Certification: UL Listed: E-14895 Listed Raintight Applicable Third Party Standards: UL Standard: 514B NEMA: FB-1 Federal Spec: W-F-408E • • • • • Type 7050SR — Type 7200SR Trade Size (inches) 1/2 3/4 1 1-1/4 1-1/2 2 Catalog Number Insulated Throat Catalog Number Dimensions in Inches Body Max Thread Length Dia. Length 7050SR 7075SR 7100SR 7125SR 7150SR 7200SR 7050SRT 7075SRT 7100SRT 7125SRT 7150SRT 7200SRT 1-29/32 1-31/32 2-1/8 2-11/16 2-31/32 3-11/32 1-5/32 1-3/8 1-3/4 2-5/32 2-7/16 2-29/32 Wt. Lbs. Per 100 7/16 7/16 15/32 17/32 9/16 23/32 15 21 32 38 48 62 Ctn. Qty. Std. Pkg. 25 25 20 5 5 2 250 250 200 25 25 10 Third Party Certification: • UL Listed: E-14895 • Listed Raintight Applicable Third Party Standards: • UL Standard: 514B • NEMA: FB-1 • Federal Spec: W-F-408E Type 6050SR — Type 6200SR Trade Size (Inches) 1/2 3/4 1 1-1/4 1-1/2 2 Catalog Number Dimension in Inches Body Length Max. Dia. 6050SR 6075SR 6100SR 6125SR 6150SR 6200SR 2-25/32 3 3-11/32 3-11/16 3-23/32 4-1/8 1-1/8 1-11/32 1-5/8 2 2-9/32 2-3/4 Wt. Lbs. Per 100 Ctn. Qty. Std. Pkg. 19 25 39 47 56 73 25 20 20 5 5 2 250 200 100 25 25 10 InspectoRidge™ Provides external visual inspection aid on outside surface, to assure raintight fittings are installed, without disassembly of conduit run. Effective September, 2008 Copyright 2008 PAGE 6 800-621-1506 www.appletonelec.com TW-1 ETP Flexel® EMT Flexible Fitting Type FLA For EMT Application • The Flexel Fitting is an innovative product in which to couple lengths of EMT together or connect EMT to a panel board, junction box, etc., when and where a change of direction is required in the conduit run. Features • Easily hand-bendable from straight tubing to 90° or any angle in between. No need to waste time using cumbersome bending equipment. • Rigid enough to maintain configuration until manually re-formed. • Wire pulls through formed bends. • Specially designed so internal diameter remains unchanged, regardless of the bend configuration. • Maintains compliance with NEC's minimum radius requirements. • Can be bent to various degrees, including offset and compound angles. • Suitable for use indoors or dry locations wherever EMT is used as a raceway. • Safely conducts the maximum ground fault current required by UL, CSA and the National Electrical Code. No need to pull a separate grounding conductor. Standard Material/Finish Flexible Length: Strip Steel/Galvanized End Fittings: Steel/Galvanized Type FLA Trade Size (inches) Catalog Number A Nominal Length 11/4 11/2 2 21/2 FLA-125 FLA-150 FLA-200 FLA-250 3 31/2 4 FLA-300 FLA-350 FLA-400 Dimensions in inches B C Radius D Max. Offset 24 29 26 29 141/2 143/4 161/4 22 73/4 93/4 131/4 16 41/2 61/2 41/4 21/2 36 38 40 22 22 261/2 17 18 19 33/4 3 11 Dimensions are approximate. Consult your local representative for details. A D TW Compliances UL Listed: E-14895 CSA Certified: LR9795 Applicable Third Party Standards: • UL Standard: 514B • CSA Standard: C22.2 No. 18 B C B Effective September, 2008 Copyright 2008 800-621-1506 www.appletonelec.com PAGE 7 TW-1 ETP Steel Liquidtight Fittings Type 4QS Type 4QS-38 — Type 4QS-200 45° and 90° TW Application • 4QS liquidtight connectors and liquidtight flexible metallic conduit are used in applications where conditions of installation, operation or maintenance require flexibility or protection from liquids, vapors or solids such as: machine tool building, motor and transformer terminations, robotics assembly, air conditioning equipment installation and Class I, Division 2 wiring Features • Tapered threaded male hub NPT • Compact, slim diameter with small turning radius • Furnished with locknut and sealing ring. • Liquidtight/Raintight/Oiltight • Suitable for grounding (through 1-1/4”) • Suitable for wet locations • Long ferrule prevents pullout and tight bend conduit “pop-out” • Suitable for use in the following Hazardous Locations: Class I, Div. 2 per NEC 501.4(B) Class I, Zone 2 per NEC 505.15(C)(2) Class II, Div. 2 per NEC 502.4(A)(1)(e) Class II, Div. 2 per NEC 502.4(B)(2) Class III, Div. 1 per NEC 503.3(A)(2) Class III, Div. 2 per NEC 503.3(B) Intrinsically Safe per NEC 504.20 • Bonding Locknuts are recommended in Hazardous Locations. See GL Series in Section CF-2, page 15. Material/Finish: Straight: Steel/Zinc Plated Angles: Body: Malleable Iron/Zinc Plated Gland nut, ferrule and locknut: Steel/Zinc Plated Third Party Certification: UL Listed: 11853 CSA Certified: 9795 UL Listed liquidtight flexible metal conduit fittings from 3/8” through 1-1/4” trade sizes are suitable for grounding under NEC 250.118(7). Applicable Third Party Standards: UL Standard: 514B CSA Standard: C22.2 No. 18 NEMA: FB-1 Federal Spec: W-F-406E Effective September, 2008 Copyright 2008 PAGE 8 Trade Size (inches) Catalog Number Insulated Throat Catalog Number Dimensions in Inches A ⁄8 (1⁄2 KO) 4QS-38 ⁄2 4QS-50 3 ⁄4 4QS-75 4QS-38T 4QS-50T 4QS-75T 1 11⁄4 11⁄2 2 4QS-100T 31⁄32 4QS-125T 13⁄16 4QS-150T 19⁄32 4QS-200T 111⁄32 3 1 4QS-100 4QS-125 4QS-150 4QS-200 ⁄ B C 7 5 ⁄32 13 ⁄16 5 ⁄8 ⁄8 5 ⁄8 13⁄32 13⁄16 17⁄16 ⁄32 ⁄64 23 ⁄32 23 ⁄32 13⁄4 25⁄32 23⁄8 27⁄8 8 23 21 43 C A B 45° Type 4QS-438 — Type 4QS-4200 Trade Size (inches) Catalog Number Insulated Throat Catalog Number Dimensions in Inches A B C 5 ⁄8 ⁄8 5 ⁄8 13⁄32 13⁄16 17⁄16 ⁄32 ⁄16 23 ⁄32 23 ⁄32 13⁄4 25⁄32 23⁄8 27⁄8 ⁄8 (1⁄2 KO) 4QS-438 ⁄2 4QS-450 3 ⁄4 4QS-475 4QS-438T 4QS-450T 4QS-475T 11⁄4 13⁄8 11⁄2 5 1 11⁄4 11⁄2 2 4QS-4100T 4QS-4125T 4QS-4150T 4QS-4200T 113⁄16 2 25⁄16 29⁄16 21 3 1 4QS-4100 4QS-4125 4QS-4150 4QS-4200 11 C B A 90° Type 4QS-938 — Type 4QS-9200 Trade Size (inches) Catalog Number ⁄8 (1⁄2 KO) 4QS-938 ⁄2 4QS-950 3 ⁄4 4QS-975 3 1 1 11⁄4 11⁄2 2 4QS-9100 4QS-9125 4QS-9150 4QS-9200 Insulated Throat Catalog Number A Dimensions in Inches 4QS-938T 4QS-950T 4QS-975T 119⁄32 121⁄32 125⁄32 4QS-9100T 4QS-9125T 4QS-9150T 4QS-9200T 23⁄16 23⁄8 25⁄8 31⁄16 B C ⁄8 ⁄8 5 ⁄8 13⁄32 13⁄16 17⁄16 5 ⁄32 ⁄16 23 ⁄32 23 ⁄32 13⁄4 25⁄32 23⁄8 27⁄8 13⁄16 11⁄4 13⁄8 111⁄16 5 5 21 11 D 5 ⁄8 ⁄ ⁄32 A 8 29 C D B 800-621-1506 www.appletonelec.com TW-1 EMT Connectors and Couplings Catalog No. Trade Size (In.) A Dimensions in Inches B C Wt. Lbs. Per 100 Ctn. Qty. Std. Pkg. Combination Couplings – EMT to Rigid Metal Conduit – Steel TWR-50 TWR-75 TWR-100 TWR-125 1/2 3/4 1 1-1/4 11/16 11/16 7/8 31/32 1/2 17/32 17/32 27/32 1 1-9/32 1-19/32 1-15/16 10.0 15.0 17.0 40.0 50 25 25 5 200 100 100 25 1-1/16 1-9/32 1-5/8 6.0 8.8 13.0 50 25 25 200 250 200 Connectors – Two Piece – Concrete Tight – Steel 92T050 92T075 92T100 1/2 3/4 1 5/16 5/16 11/32 11/32 7/16 13/32 TW Effective September, 2005 Copyright 2005 800-621-1506 www.appletonelec.com PAGE 9 TW-1 ® TW Effective September, 2005 Copyright 2005 PAGE 10 800-621-1506 www.appletonelec.com TW-2 EMT Couplings, 90˚ Connectors and Caps/Heads Catalog No. Trade Size (In.) Dimensions in Inches A B C Wt. Lbs. Per 100 Ctn. Qty. Std. Pkg. Combination Coupling – EMT to Flexible Metal Conduit Pressure Cast TW38-50DC† 1/2 1-9/32 1-1/4 15/16 7.5 25 100 Combination Coupling - EMT to Flexible Metal Conduit Malleable Body/Nut TWCC38-50† 1/2 27/32 5/8 1-1/16 12.0 10 100 TWCC-50 1/2 7/8 5/8 1-1/16 14.5 10 100 TWCC-75 3/4 1-1/16 21/32 1-5/16 25.0 10 100 TWCC-100 1 1-3/16 27/32 1-7/8 61.0 5 50 1-7/8 2-1/16 19/32 32.0 25 100 2-3/16 2-7/16 7/16 50.0 10 50 2-19/32 3 7/16 105.0 5 25 2-13/16 3-5/16 9/16 136.0 5 25 1-7/32 1-5/16 13/32 20.0 25 100 1-5/16 1-7/16 7/16 30.0 10 100 1-5/8 1-9/16 7/16 53.0 5 50 2-7/8 3-5/8 64.0 — 10 Gland Compression 90° Long Connectors – Concrete Tight Malleable – Steel Nut TWLL-50L 1/2 TWLL-75L 3/4 TWLL-100L 1 TWLL-125L 1-1/4 Male End Has Locknut TW Gland Compression 90° Short Connectors – Concrete Tight Malleable – Steel Nut TWL-50L 1/2 TWL-75L 3/4 TWL-100L 1 Male End Has Locknut Set Screw Entrance Caps – Malleable Iron – Exclusive “Snap-On” Cover EF-125 1-1/4 (3) 5/8” and (2) 13/32” EF-150 1-1/2 (3) 25/32”, (2) 9/16” and (1) 3/8” 5 3-5/16 4-11/32 93.0 — 10 EF-200 2 (3) 1”, (2) 3/4 and (3) 17/32” 6-11/32 4-1/2 5-9/16 183.0 — 5 EF-250 2-1/2 (3) 7/8”, (1) 1” and (3) 1-5/16” 9 6-1/4 7-3/4 350.0 — 1 4-5/16 † Not UL Listed. Effective September, 2005 Copyright 2005 800-621-1506 www.appletonelec.com PAGE 1 TW-2 EMT Adapters, Clamps and Straps Catalog No. Trade Size (In.) A Dimensions in Inches B C Wt. Lbs. Per 100 Ctn. Qty. Std. Pkg. Steel No-Thread to Threaded Fittings – Conversion Adapters TWAD-50 TWAD-75 TWAD-100 TWAD-125 TWAD-150 TWAD-200 1/2 3/4 1 1-1/4 1-1/2 2 7/16 1/2 5/8 3/4 3/4 3/4 1/8 1/8 1/8 3/16 3/16 1/4 1 1-7/16 1-1/2 2 2-1/4 2-13/16 2.2 4.0 6.0 11.0 12.0 19.0 50 25 10 10 5 5 200 100 100 100 100 100 Steel – Clamps – EMT TWCL-50 TWCL-75 TWCL-100 TWCL-125 TWCL-150 TWCL-200 1/2 3/4 1 1-1/4 1-1/2 2 15/16 1-1/32 1-5/32 1-11/32 1-11/16 1-27/32 15/32 17/32 7/16 1/2 19/32 5/8 11/16 29/32 1-1/8 1-15/32 1-11/16 2-5/32 3.4 4.6 6.5 10.0 19.0 25.0 100 100 50 50 50 5 1000 1000 100 100 100 25 CL-250 CL-300 CL-350 CL-400 2-1/2 3 3-1/2 4 2-13/16 3-5/16 3-7/16 3-25/32 1-1/8 1-5/16 1-5/8 1-5/8 2-3/4 3-3/8 3-7/8 4-3/8 76.0 89.0 112.0 128.0 5 — — — 25 10 10 10 Catalog No. Trade Size (In.) A Wt. Lbs. Per 100 Ctn. Qty. Std. Pkg. Dimensions in Inches B C D Malleable – Clamps – EMT D TW B C A TWCL-50MN TWCL-75MN TWCL-100MN TWCL-125MN TWCL-150MN TWCL-200MN 1/2 3/4 1 1-1/4 1-1/2 2 1-1/16 1-3/16 1-3/8 1-5/8 1-13/16 2-5/16 7/8 1-1/16 1-3/8 1-3/4 1-15/16 2-1/2 5/8 3/4 13/16 7/8 15/16 1-1/16 1/4 1/4 1/4 3/8 3/8 1/2 5.0 6.0 10.0 13.0 15.0 20.0 100 50 50 25 25 25 1000 500 250 250 100 100 CL-250MN CL-300MN CL-350MN CL-400MN 2-1/2 3 3-1/2 4 2-9/16 3-3/16 3-3/8 3-3/4 3 3-13/16 4-7/16 5 1-5/16 1-1/2 1-11/16 1-15/16 1/2 1/2 5/8 5/8 71.0 107.0 172.0 266.0 5 5 2 2 25 25 10 10 Catalog No. Trade Size (In.) A Ctn. Qty. Std. Pkg. Dimensions in Inches B C Wt. Lbs. Per 100 Steel Pipe Straps – Two Hole – EMT Effective September, 2005 Copyright 2005 PAGE 2 TW2500 TW2750 TW2100 TW2125 TW2150 TW2200 1/2 3/4 1 1-1/4 1-1/2 2 1-1/2 1-3/4 2-3/32 2-19/32 2-11/16 3-1/2 2-1/32 2-13/32 2-13/16 3-5/16 3-7/16 4-3/4 5/8 5/8 5/8 3/4 3/4 15/16 1.0 1.6 2.0 4.0 4.0 4.7 — — — — — 25 250 250 100 100 100 100 CF250-H CF300-H CF350-H CF400-H 2-1/2 3 3-1/2 4 4-3/8 5 6-1/4 7 5-5/8 6-1/4 7-1/4 8 3-1/32 1 1 1-1/4 5.7 8.0 8.7 9.4 25 25 25 10 100 100 50 50 800-621-1506 www.appletonelec.com TW-2 EMT Display Pack Benders and EMT Benders Catalog No. EMT Rigid Bending Suggested* Wt. Lbs. Ctn. Std. Size (In.) Size (In.) Radius Handle Per 100 Qty. Pkg. 4” BPH-75 221.0 1 10 Standard Benders – With Degree Scale B-1† 1/2 B-2 3/4 1/2 5” BPH-75 355.0 1 10 B-3 1 3/4 6” BPH-100 681.0 1 4 — B-1 “Powr-Jack”® Benders – With Booster Step and Degree Scale BJ-5 BJ-5 1 3/4 6” BPH-100 742.0 1 2 BJ-6 1-1/4 1 9” BPH-125 1762.0 — 1 BPH-75 492.0 1 10 Double Groove Benders – With Degree Scale B-9 BJ-9 — 3” 3/4 1/2 4” TW BJ-6 1/2 High Strength Steel Handles – With Zip Guide BPH-75†† Use with 38” Long, 3/4” I.P.S. B-1, B-2, B-9 360.0 1 10 BPH-100 44” Long, 1” I.P.S. B-3, BJ-5 460.0 1 5 BPH-125 54” Long, 1-1/4” I.P.S. BJ-6 400.0 1 4 * Handles are not included and must be ordered separately from this page. † Display pack †† Expanded end serves as stub straightener. Effective September, 2005 Copyright 2005 800-621-1506 www.appletonelec.com PAGE 3 TW-2 ® TW Effective September, 2005 Copyright 2005 PAGE 4 800-621-1506 www.appletonelec.com