Whites, EE 320
Lecture 10
Page 1 of 9
Lecture 10: Bipolar Junction Transistor
Construction. NPN Physical Operation.
For the remainder of this semester we will be studying
transistors and transistor circuits.
The transistor is a three terminal device. It is probably only the
second such device you’ve encountered in electrical
engineering, after the op amp. Roughly speaking, the transistor
acts an electronic valve: the node current or voltage at one
terminal controls the current entering the second terminal and
exiting the third.
It would be difficult to overstate the importance of the transistor
to electronics. Some of its uses are:
Digital logic
Memory circuits
Amplifiers
Electronic switches.
The two basic families of transistors are bipolar junction
transistors (BJTs) and field effect transistors (FETs). We’ll start
by discussing BJTs for approximately 15 lectures followed by
FETs for the remaining 12 lectures. BJTs are covered in Chapter
6 of your text.
© 2016 Keith W. Whites
Whites, EE 320
Lecture 10
Page 2 of 9
BJT Physical Structure
BJTs are formed from three doped regions on a silicon crystal.
These can either be npn doped regions or pnp. A simplified
sketch of an npn transistor is:
(Fig. 6.1)
As can be seen, the BJT is formed from two back-to-back pn
junctions:
Emitter-base junction (EBJ)
Collector-base junction (CBJ).
This specific way of drawing the BJT has been around from the
very beginning of these transistors. This figure:
is from William Shockley’s U.S. patent 2,569,347 issued in
1951.
Whites, EE 320
Lecture 10
Page 3 of 9
BJTs can also be fabricated from two p-type regions and one ntype. This is called a pnp transistor:
(Fig. 6.2)
While the BJT might appear to be symmetrical by looking at
Fig. 6.1, the actual devices are not.
For example, the cross section below of an npn transistor clearly
shows that the EBJ and CBJ, for example, have very differently
sized surface contact areas, which will greatly change their
relative behaviors.
(Fig. 6.7)
There are four basic modes of operation for a BJT depending on
the states of the two pn junctions of the transistor:
Whites, EE 320
Lecture 10
Mode
Cutoff
Active
Saturation
Reverse Active
Emitter-Base Jct.
Reverse
Forward
Forward
Reverse
Page 4 of 9
Collector-Base Jct.
Reverse
Reverse
Forward
Forward
In digital logic applications, the transistor switches between the
cutoff and saturation modes. As a linear amplifier in a
communication circuit, the transistor would operate in the active
mode.
Because of the asymmetrical physical construction, the reverse
active mode is not the same as interchanging the collector and
emitter leads.
The states of the two pn junctions can be altered by the external
circuitry connected to the transistor. This is called biasing the
transistor.
NPN Transistor in the Active Mode
We’ll begin the discussion of the BJT physical operation by
considering an npn transistor in the active mode. To bias it in the
active mode, we need to forward bias the EBJ and reverse bias
Whites, EE 320
Lecture 10
Page 5 of 9
the CBJ (notice that the emitter and collectors have swapped
positions from Fig. 6.1 shown earlier):
(Fig. 1)
The overall objective of this circuit is to create a current flowing
from the collector to the emitter terminals in the transistor that is
“controlled,” so to speak, by the base voltage VBB.
How does the transistor operate in this circuit?
Because of the forward bias on the EBJ, charges can flow
across this junction giving rise to iE. This current is
primarily electrons that are injected from n to p.
The electrons injected in the base diffuse across the thin
base region towards the collector. Some of the e- recombine
in the base, but this region is manufactured to be thin and
lightly doped compared to the emitter so this recombination
is kept small. Otherwise, the BJT would just operate as two
back-to-back diodes and no current would flow through the
collector.
Whites, EE 320
Lecture 10
Page 6 of 9
A representative “minority carrier” concentration profile is
shown below in Fig. 6.4. (Note that C and E are switched with
reference to Fig. 1 above.)
(Fig. 6.4)
The e- that reach the reverse-biased CBJ encounter a large
electric field. This E sweeps them into the collector
forming the collector current iC as shown in Fig. 1 above.
A small base current iB is present largely due to
recombination in the base with the small amount of injected
holes from the base to the emitter. This is an important
current, though.
Discussion About BJT in the Active Mode
1. The proportion of electrons from the emitter that “make it” to
the base when the transistor operates in the active mode is
called the collector efficiency, :
Whites, EE 320
Lecture 10
Page 7 of 9
iC
or iC iE
(6.7),(1)
iE
Typically it has values of near 0.99. Note that is called the
common-base current gain in the text.
From KCL in the circuit of Fig. 1 (noticing the defined
directions of the currents):
iE iB iC
(6.4),(2)
or
iB iE iC 1 iE
(3)
We can deduce from (3) that with 1, then iB will be much,
much smaller than iE.
2. The ratio of collector current to base current when the
transistor operates in the active mode is called the current
gain, :
i
C or iC iB
(6.2),(4)
iB
3. Dividing (1) by (4) we find that
iC
iB 1
Equating this to (4) we find
1
and solving this equation for
(6.10),(5)
Whites, EE 320
Lecture 10
1
Page 8 of 9
(6.8),(6)
With 0.99 100 .
4. One can think of the base current in the BJT operating in the
active mode as controlling the collector current: iC iB .
Since is large, then a small change in iB produces a large
change in iC. If the base were an input signal and the collector
the output, then this would be signal amplification!
Awesome!
5. The circuit symbol and current conventions for the npn BJT
are
The arrows indicate the assumed directions for positive
current for the npn BJT. The filled arrow is always located on
the emitter and helps us to remember the direction of the
emitter current.
6. For biasing in the active mode as shown in Fig. 1, one biasing
circuit might be
Whites, EE 320
Lecture 10
Page 9 of 9
(Fig. 6.13)
0
